Initialen



Change color to default
Change color to red
Change color to blue
Change color to green
Change color to yellow
Change color to cyan
Change color to magenta
Change color to orange
Change color to b/w

Linux on Dialogue Flybook Howto - fuschlberger.net

Change color to default
Change color to red
Change color to dark red
Change color to blue
Change color to dark blue
Change color to green
Change color to dark green
Change color to yellow
Change color to dark yellow
Change color to cyan
Change color to dark cyan
Change color to magenta
Change color to dark magenta
Change color to magenta
Change color to dark orange
Change color to grey
Change color to b/w

Printme!

Kernel

This is the .config-file of my 2.6.14.3 kernel.

This is the .config-file of my 2.6.17.1 kernel.

The contents of my /etc/modules for 2.6.14.3:
psmouse
8139too
trident
penmountlpc

I am now using udev and hotplug.

This is the .config-file of my 2.6.12 kernel.

The relevant parts of my /etc/usbmgr/usbmgr.conf for 2.6.12:
host ehci-hcd

The contents of my /etc/usbmgr/preload.conf for 2.6.12:
usbhid
evdev

This is the .config-file of my 2.4.30 kernel.

The most important settings for 2.4.30 are listed below:

Processor type and features

(Crusoe) Processor family
<*> /dev/cpu/microcode - Intel IA32 CPU microcode support
<*> /dev/cpu/*/msr - Model-specific register support
<*> /dev/cpu/*/cpuid - CPU information support

General setup

PCMCIA/CardBus support

[*] CardBus support
[*] i82365 compatible bridge support

ACPI Support

[*] ACPI Support
<*> AC Adapter
<*> Battery
<*> Button
<*> Fan
<*> Processor
<*> Thermal Zone

Fan and Thermal are not supported.

ATA/IDE/MFM/RLL support

<*> ATA/IDE/MFM/RLL support

IDE, ATA and ATAPI Block devices

[*] PCI IDE chipset support
[*] Generic PCI IDE Chipset Support
[*] Sharing PCI IDE interrupts support
[*] Generic PCI bus-master DMA support
[ ] Boot off-board chipsets first support
[ ] Force enable legacy 2.0.X HOSTS to use DMA
[*] Use PCI DMA by default when available
[ ] Enable DMA only for disks
[ ] ATA Work(s) In Progress (EXPERIMENTAL)
< > Pacific Digital ADMA-100 basic support
< > AEC62XX chipset support
<*> ALI M15x3 chipset support
[ ] ALI M15x3 WDC support (DANGEROUS)

Without the ALI 15x3 support the Harddisk is not recognized.

Network device support

Ethernet (10 or 100Mbit)
<M> RealTek RTL-8139 PCI Fast Ethernet Adapter support

Input core support

<M> Input core support
<M> Input core support
<M> Mouse support
(1024) Horizontal screen resolution
(768) Vertical screen resolution
<M> Event interface support

Sound

<*> Sound card support
<M> Trident 4DWave DX/NX, SiS 7018 or ALi 5451 PCI Audio Core

USB support

<M> EHCI HCD (USB 2.0) support (EXPERIMENTAL)
<M> OHCI (Compaq, iMacs, OPTi, SiS, ALi, ...) support
<M> USB Human Interface Device (full HID) support
[*] HID input layer support

Bluetooth support

<M> Bluetooth subsystem support
<M> L2CAP protocol support
<M> SCO links support
<M> RFCOMM protocol support
[*] RFCOMM TTY support

Bluetooth device drivers

<M> HCI USB driver


Change color to defaultChange color to redChange color to blueChange color to greenChange color to yellowChange color to cyanChange color to magentaChange color to orangeChange color to b/w

© 2014 by wf
webslave (at) fuschlberger.net
Medieninhaber:
Wolfgang Fuschlberger, Salzburg

[Valid-HTML-4.01]